PT-100 MPPT Charge Controller

PT-100

Maximize Energy Harvest and Improve Battery Life

The PT-100 is a Maximum Power Point Tracker (MPPT) charge controller designed to harvest the maximum available energy from the PV array and deliver it to the batteries.

The PT-100’s MPPT algorithm finds the maximum power point of the array and operates at this point while regulating the output current and battery voltage to fully charge the battery.

For our online PV Array Calculator for the Magnum Energy PT-100 Charge Controller: Visit Here

Watch Our PT-100 Video Series

Setup a PT-100 Charge Controller with the ME-ARC Remote
Understand the ME-ARC Remote Meter Screens for the PT-100 Charge Controller
Setup the PT-100 Charge Controller with the ME-ARTR Router
ME-ARTR and the Meter Screens for the PT-100 Charge Controller
How to Install the PT-100 Charge Controller to the MP Panel System with Charge Controller Bracket
FULL PLAYLIST

Product Controllers

Output Current

100 amps

Battery Voltage

12, 24, or 48 V

MPPT

Yes

Power Consumption

< 4 watts (fan off, display/LEDs off)

Maximum PV input voltage (any condition)

200 VDC + battery voltage or 240 VDC - whichever is lower

Maximum PV operating voltage

187 VDC

Maximum PV array short circuit current

100 ADC

Nominal battery voltage range

12, 24, or 48 VDC

Battery charger output voltage range

10 to 66 VDC

Continuous charger output current

100 ADC (from -20°C to +40°C) with proportional power reduction up to 60°C ambient

Maximum output power

6600 watts

Efficiency

99% typical

Charger regulation method

Automatic three-stage (bulk, absorption, float) charge with manual equalization

Battery temperature compensation

With Battery Temperature Sensor (BTS) connected (battery temperature -20 °C to +55 °C)

Internal cooling

Using dual ball-bearing fans for long life

Overcurrent protection

With two overlapping circuits

Over-temperature protection

On transformer and MOSFETS

Listings

ETL Listed to UL/cUL 1741, CSA C22.2 #107.1-01

Warranty

Five years parts and labor

Operating temperature

-20° C to +60° C (-4° F to 140° F)

Nonoperating temperature

-40° C to +70° C (-40° F to 158° F)

Operating humidity

0 to 95% RH non condensing

Enclosure type

Indoor, ventilated, with removable powder-coated conduit box

Unit dimensions (w x h x d)

8.5" x 15.5" x 4.0" (21.6 cm x 39.4 cm x 10.2 cm)

Shipping dimensions (w x h x d)

11.5” x 19.5” x 8.125” (29.2 cm x 49.5 cm x 20.6 cm)

Mounting

Mounted on a vertical surface (wall) or installed on MP or MMP enclosure

Weight

13.6 lb (6.2 kg)

Shipping weight

18 lb (8.2 kg)

Max operating altitude

15,000’ (4570 m)

MPPT

Maximum Power Point Tracking technology for increased PV power output efficiency.

Multi-state Charging:

Maximizes system performance and improves battery life.

Optimal Battery Charging:

Maximizes system performance and improves battery life.

Voltage Options:

Compatible with 12, 24, or 48V battery systems with automatic detection of system voltage.

Integrated Ground-fault Detection:

Integrated PV Ground- Fault Detection and Interruption/ Indication, with pre-fault leakage/ diagnostic metering.

Extensive Electronic Protection:

Over-temperature protection, power derating when temperature is high, PV short circuit and high PV input shutdown, output overcurrent protection and night-time back-feed (reverse current) protection.

Support a Large PV Array:

A single controller supports a large PV array up to 6600W.

High Efficiency:

The PT-100 provides higher than 99% conversion efficiency and uses less than two watts of power in nighttime mode.

LED Indicators and Screen

Multiple LED indicators and large digital LED screen on front panel for easy-to-read system information.

Integrated Arc-fault Circuit Interrupter:

An integrated PV Arc- Fault Circuit Interrupter detects, indicates, and extinguishes series arcs. The AFCI is designed to meet the new National Electric Code (NEC) Article 690.11 requirements.

Convenient Installation

Run all of the wiring to the unique, remain-in- place wiring box with ease prior to installing the full PT-100 unit.

On-site Updates

The PT-100’s software can be updated on site.

Easy MP and MMP integration

The PT-100 is designed to work with a Magnum Panel (MP) or Mini-Magnum Panel (MMP). It provides room and access to PV and battery disconnect breakers.

Download Owners Manual (17.57 MB)

Download Firmware Update (17.66 MB)

3D Images (6.78 MB)

There are no related products included at this time